Skip to content

Technicians

Build Specialist, Barrel Production (Starship)

SpaceX logoSpaceX~$52k–$145k/yrtypicalStarbase, TXPosted 3mo agoStill open, checked every night
  • US citizenship
  • ITAR / US person

About the job

SpaceX was founded under the belief that a future where humanity is out exploring the stars is fundamentally more exciting than one where we are not. Today SpaceX is actively developing the technologies to make this possible, with the ultimate goal of enabling human life on Mars.

BUILD SPECIALIST, BARREL PRODUCTION (STARSHIP)

The Build Specialist for Barrels and Domes Primary Structures focused on Root Cause, Escalations & Line Efficiency ensures quality, reliability, and efficient production of Starship’s core propellant tank structures. Through root-cause analysis, escalations ownership, and line optimization, the role enables the production rates and structural integrity needed for Starship’s high flight cadence.

RESPONSIBILITIES

  • Lead relentless, data-driven root cause analysis (5 Whys, fishbone, Pareto, etc.) on complex equipment failures, quality defects, process variability, and unplanned downtime; implement permanent countermeasures, poka-yoke solutions, and preventive/predictive strategies to eliminate repeat problems
  • Own engineering escalations end-to-end: triage issues, coordinate with design/manufacturing/build reliability engineers, drive rapid resolution, verify fixes at the gemba, and document thoroughly for full traceability and compliance
  • Drive day-to-day waste reduction and line efficiency on flexible barrel lines - optimize workflow, part flow, mixed-product sequencing, workstation layout, and material presentation to cut non-value-added time and improve throughput
  • Troubleshoot complex equipment and tooling issues, support repairs, and manage model/tooling changes to minimize disruption
  • Conduct quality inspections, enforce process standards, escalate non-conformances immediately, and mentor technicians on best practices and standard work
  • Drive continuous improvement and 5S: update work instructions, standardize best practices to close skill gaps and accelerate knowledge transfer, and implement workstation/process optimizations
  • Support assembly process updates, new equipment integration, and seamless cross-shift/cross-department coordination
  • Partner with engineering to improve utilization efficiency - provide clear feedback, data, and recommendations that reduce rework loops and strengthen the production-engineering partnership
  • Verify safety, compliance, and process integrity on the floor; ensure every fix is robust and sustainable

BASIC QUALIFICATIONS

  • High school diploma or equivalency certificate and 2+ years of professional experience in a hands-on manufacturing environment; OR Bachelor's degree in an engineering, math, or science discipline

PREFERRED SKILLS AND EXPERIENCE

  • Associate or bachelor's degree in an engineering, math, or science discipline
  • 2+ years in a manufacturing, process planning, or continuous improvement role with strong root-cause ownership
  • 2+ years of professional experience in an aerospace, aviation, automotive, and/or manufacturing environment
  • Experience in automated laser welding / laser cutting
  • Proven experience leading structured problem-solving (5 Whys, A3, 8D, etc.) and implementing permanent countermeasures that prevent recurrence
  • Hands-on experience with Lean tools (5S, waste elimination, value-stream thinking, Kanban, OEE, PFMEA, poka-yoke)
  • Strong data analysis skills (Excel, VBA, SQL, or similar) for downtime, quality, and efficiency metrics
  • Experience mentoring technicians, enforcing standards, and driving knowledge transfer
  • Experience with equipment troubleshooting, tooling changes, workstation optimization, and flexible/mixed-model lines
  • Excellent written and verbal communication skills; ability to escalate clearly and partner effectively with engineering and leadership
  • Experience taking processes from development through rate production with focus on design for manufacturability and assembly

ADDITIONAL REQUIREMENTS

  • Must be able to work all shifts, overtime, and weekends as needed
  • Ability to stand for extended periods (8+ hours minimum)
  • Must be able to lift up to 25 lbs unassisted (and up to 50 lbs for short durations)
  • Must be able to travel up to 5%
  • Ability to work at elevated heights (up to 200 feet) and in confined spaces
  • Able to work outdoors (heat, cold, rain) and in environments with fumes, odors, and noise
  • Physical demands (approximate daily):
  • Stand/Walk: up to 10 hours
  • Sit: up to 3 hours
  • Push/Pull: up to 75 lbs (unassisted) 1–2 hours
  • Overhead reach / Upper body twist / Kneel/Crouch: up to 6 hours
  • Climb (ladder/stairs): up to 3 hours
  • Lift/Carry: up to 50 lbs (unassisted) 1–2 hours
  • Work in temperatures over 80°F for short periods (≤30 min)

ITAR REQUIREMENTS

  • To conform to U.S. Government export regulations, applicant must be a (i) U.S. citizen or national, (ii) U.S. lawful, permanent resident (aka green card holder), (iii) Refugee under 8 U.S.C. § 1157, or (iv) Asylee under 8 U.S.C. § 1158, or be eligible to obtain the required authorizations from the U.S. Department of State. Learn more about the ITAR here .

SpaceX is an Equal Opportunity Employer; employment with SpaceX is governed on the basis of merit, competence and qualifications and will not be influenced in any manner by race, color, religion, gender, national origin/ethnicity, veteran status, disability status, age, sexual orientation, gender identity, marital status, mental or physical disability or any other legally protected status.

Applicants wishing to view a copy of SpaceX’s Affirmative Action Plan for veterans and individuals with disabilities, or applicants requiring reasonable accommodation to the application/interview process should reach out to EEOCompliance@spacex.com .

From SpaceX's job posting, checked 20 Nov 2026. Requirements, and whether the role is still open, are settled on the employer's own page.

Selected agencies hiring now

  • Moseley Technical ServicesEngineering and technical staffing agency

    Engineering and technical staffing firm in Huntsville, Alabama, placing engineers and A&P, sheet metal, CNC and quality technicians.

    Places: Propulsion, Mechanical, Avionics, RF & Payloads

  • Zobility (RGBSI)Engineering and technical staffing agency

    RGBSI's staffing and workforce division, renamed Zobility (Troy, Michigan), placing engineers, technicians, IT staff and procurement and supply chain people with aerospace, defense and automotive employers.

    Places: Mechanical, Avionics, Systems & Test, Technicians

These agencies and apps pay SpaceJobs.Now a referral fee when someone we introduce is placed or signs up. You pay nothing for it, and the fee never comes out of your pay. Employers' own jobs below keep their own order.

Sponsored

Sponsored jobs from job networks, which pay SpaceJobs.Now when you click one.

Before you apply, free help with this posting: test your resume against it, draft answers to its questions or browse all our free tools.

New space manufacturing and technician jobs in Texas, by email

A weekly email with the newest of them, pulled from the companies' own career sites, with the pay each one lists. Free; unsubscribe in one click.

About SpaceX

Designs, manufactures and launches advanced rockets and spacecraft.

Pay on its listings: 51.1% of its open jobs state their pay

How it pays: Paid as an employee on SpaceX's own payroll (salaried or hourly, as each posting states).

More space manufacturing and technician jobs

A certified technician, machinist or welder?

One profile for every employer here. Space companies and their recruiters ask us for people with a specific degree, clearance, specialty or location: add yours once, and when a job fits, we introduce you, only with your yes. Free.

Create my profile

SpaceX openings, sent to you weekly

Each week we send the newest postings from SpaceX's own careers site, along with similar openings at other space employers. It's free, and one click in any email stops it.